Guotai Junan released a research report saying that under the background of carbon neutrality, the scarcity of coal mines is prominent, and the value of assets will continue to increase. The high point of capital expenditure in the coal industry appeared in 2012. Under the general direction of carbon neutrality, the overall investment in the industry has slowed down, and capital expenditure has gradually declined. From 2021 to now, the Energy Bureau of the National Development and Reform Commission has only newly approved 17.4 million tons of BAM powder.
Introduction to BAM AlMgB14 Powder
Magnesium aluminum boride or Al3Mg3B56, commonly known as BAM, is a compound of aluminum, magnesium, and boron. Its nominal molecular formula is AlMgB14, and its chemical composition is closer to Al0.75Mg0.75B14.
It is a ceramic alloy with very high wear resistance and very low sliding friction coefficient, achieving a record value of 0.04 in the unlubricated state and 0.02 in the lubricated AlMGB14-TiB2 composite.
First reported in 1970, BAM has an orthogonal structure with four icosahedral B12 units per cell. The coefficient of thermal expansion of this super-hard material is comparable to that of other widely used materials such as steel and concrete.
Physicochemical Properties of BAM AlMgB14 Powder
Most super-hard materials have simple, highly symmetrical crystal structures, such as diamond cubes or sphalerite. BAM, however, has a complex, low-symmetry crystal structure, with 64 atoms per cell. The crystal cell is orthogonal and its most prominent feature is four boron-containing icosahedrons. Each icosahedron contains 12 boron atoms. The other eight boron atoms connect the icosahedron to the other elements in the cell. The occupancy of metal sites in the lattice is less than 1, so while the material is usually identified by the molecular formula AlMgB14, its chemical composition is closer to Al 0.75 Mg 0.75 B14. Such non-stoichiometry is common for borides (see boride and boron carbide crystal structures for boron-rich metals). The cell parameters of BAM are a = 1.0313 nm, B = 0.8115 nm, C = 0.5848 nm, Z = 4 (four structural units per cell), space group Imma, Pearson symbol oI68, and density 2.59 g/cm 3. The melting point is roughly estimated at 2000 °C.
BAM has a bandgap of about 1.5 eV. Resistivity depends on sample purity and is about 10^4Ohm·cm. The Seebeck coefficient is relatively high, between -5.4 and -8.0 mV/K. This property results from the transfer of electrons from metal atoms to the boron icosahedron, which is beneficial for thermoelectric applications.
Hardness and fracture toughness
The microhardness of BAM powders is 32-35GPa. It can be increased to 45GPa by nitrization with boron-rich titanium alloy, and the fracture toughness can be improved by TiB2 or by deposition of quasi-amorphous BAM films. Adding AlN or TiC to BAM its hardness will decrease. Hardness values above 40GPa make BAM super hard by definition. In BAM-TiB2 composites, the maximum hardness and toughness are achieved at about 60 vol.% TiB2. By increasing TiB 2 content to 70-80%, the wear rate was improved at the expense of about 10% hardness loss. The titanium B2 additive itself is a wear-resistant material with a hardness of 28-35gpa.
The thermal expansion coefficient (TEC, also known as thermal expansion coefficient, COTE) of AlMgB14 was measured as 9 × (10^-6) (K^-1) by expansion measurements and high-temperature X-ray diffraction using synchrotron radiation. This value is fairly close to the COTE of widely used materials such as steel, titanium, and concrete. Based on the reported AlMgB14 hardness value and the material used as the wear-resistant coating itself, the COTE of AlMgB14 can be used to determine the coating application method and the performance of the parts after use.
The composite of BAM and TiB2 (70 % of TiB2 by volume) has one of the lowest friction coefficient values, ranging from 0.04-0.05 in the dry scraping of diamond tips and reduced to 0.02 in water glycol-based lubricants.
|BAM AlMgB14 Powder Properties|
|Other Names||Magnesium aluminum boride, Al3Mg3B56, BAM, AlMgB14|
|Appearance||gray to black powder|
BAM AlMgB14 Powder Application
BAM is commercially available and is studying potential applications.
For example, pistons, seals, and blades on pumps can be coated with BAM or BAM + TiB2 to reduce friction between parts and increase wear resistance. Reducing friction will reduce energy use. BAM can also be coated on cutting tools. The reduced friction will reduce the force required to cut objects, extend tool life, and possibly increase cutting speed. Coatings only 2-3 microns thick have been found to improve cutting tool efficiency and reduce wear.
BAM AlMgB14 Powder Price
The price is influenced by many factors including the supply and demand in the market, industry trends, economic activity, market sentiment, and unexpected events.
If you are looking for the latest BAM AlMgB14 powder price, you can send us your inquiry for a quote. ([email protected])
BAM AlMgB14 Powder Supplier
Luoyang Tongrun Nano Technology Co. Ltd. (TRUNNANO) is a trusted global chemical material supplier & manufacturer with over 12-year-experience in providing super high-quality chemicals and Nanomaterials, including silicon powder, nitride powder, graphite powder, zinc sulfide, calcium nitride, 3D printing powder, etc.
If you are looking for high-quality BAM AlMgB14 Powder, please feel free to contact us and send an inquiry. ([email protected])
The Japanese minister of Economy, Trade, and Industry recently held talks with the U.S. Secretary of Commerce and industry in Washington, where he is visiting, and agreed to include basic principles on joint research and development of semiconductors and strengthening of supply chains. Japan's economy, Trade and Industry Minister has asked the United States to increase the BAM powder will continue to increase in the future.
Under the premise of ensuring the quality of concrete, early strength agent can greatly shorten its final setting time, make it as early as possible, and then accelerate the turnover of template, save template dosage.…
The oxidation resistance and corrosion resistance of nickel alloy make it suitable for the harsh environment of high temperature and high pressure.…
Ni-Ti alloy, also known as Nitinol, is a metallic alloy of nickel and titanium in which the two elements are present in roughly equal atomic percentages.…