www.kxcad.net Home > CAM Index > EdgeCAM Index >
|
Call ID |
Description |
Closing Notes |
|
26721 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
30504 |
Requirement for specific open pocket roughing cycle. |
Implemented |
|
30753 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
32107 |
Memory - Roughing out of memory on some large parts |
Supplied parts now generate a toolpath |
|
38628 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
39201 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
44483 |
Facemill - enable leads on all passes with optimised |
With optimised checked you can now specify to apply leads to all cuts or just the first and last pass. |
|
44860 |
Roughing - internal open pocket cannot be machined |
Fixed |
|
46276 |
Roughing - internal open pocket cannot be machined |
Fixed |
|
47101 |
Simulator - Solid parts digitised as stock fail to go into Simulator |
Solid stock is now healed where possible. |
|
47930 |
Enhancement - open pocket feature cycle |
Implemented |
|
48198 |
Memory - Roughing out of memory on some large parts |
Supplied parts now generate a toolpath |
|
48877 |
Facemill - enable leads on all passes with optimised |
With optimised checked you can now specify to apply leads to all cuts or just the first and last pass. |
|
49599 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
49726 |
Simulator - Solid parts digitised as stock fail to go into Simulator |
Solid stock is now healed where possible. |
|
51929 |
Facemill - enable leads on all passes with optimised |
With optimised checked you can now specify to apply leads to all cuts or just the first and last pass. |
|
51953 |
Profile Operation - material side fails with multiple features |
Fixed with new Features and New Profiling Cycle. |
|
52228 |
Enhancement request for a solid model alignment tool in milling |
Implemented |
|
53226 |
Enhancement - ability to measure distance between holes centers |
New Hole Features can be measured accurately. |
|
53497 |
Surface operation uses superceded cycle |
The Surface Operation has been retired from the interface. Users should use the Profile and Rough Operations |
|
53621 |
"Feature Find - Countersink counterbored hole should be 1 feature, not 2" |
Fixed in New Hole Feature |
|
53731 |
"Simulator - add part comparison facility, currently only availablin rapid result" |
Comparison facilty added to Simulator |
|
53965 |
Roughing - internal open pocket cannot be machined |
Fixed |
|
54399 |
Memory - Roughing out of memory on some large parts |
Supplied parts now generate a toolpath |
|
54480 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
54492 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
54623 |
Simulator - does not report index move collisions |
Fixed |
|
54756 |
"Boundary Enhancements - cut on, cut to and tangent to options" |
Implemented |
|
54867 |
"Simulator - add part comparison facility, currently only availablin rapid result" |
Comparison facilty added to Simulator |
|
55244 |
Enhancement - Use roughing tool option on pocket operation |
Obsolete. Superseded by New Roughing and Profiling Operations. |
|
55344 |
Enhancement request for a solid model alignment tool in milling |
Implemented |
|
56610 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
56901 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
57065 |
Simulator - does not report index move collisions |
Fixed |
|
57246 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
57859 |
Browser doesn't display Hole Operation |
Fixed |
|
58503 |
Profile operation - fails to generate correct toolpath on pocket feature |
Solved with the new Profiling Operation. |
|
58998 |
Enhancement - Hole operation in rotary axial turn optimisation |
Implemented the Optimise Toolpath Modifier |
|
59436 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
59522 |
"Boundary Enhancements - cut on, cut to and tangent to options" |
Implemented |
|
59984 |
Profile Operation - material side fails with multiple features |
Fixed with new Features and New Profiling Cycle. |
|
60872 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
60947 |
"Boundary Enhancements - cut on, cut to and tangent to options" |
Implemented |
|
61554 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
61577 |
Template - Adaptive Milling - support High Speed M/C in the Toolchange |
"High Speed Mode and Coolant modifiers added to ""More"" Tab of Toolchange Dialog." |
|
61721 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
62431 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
62940 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
63136 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
63459 |
Enhancement request for a solid model alignment tool in milling |
Implemented |
|
64036 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
64197 |
PCI Directive - QUERY shouldn't crash if deleted/blank entity is selected |
Use format %QUERY=nRet=[EntNo] (include nRet for avoiding the crash) |
|
64348 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
64430 |
"Facemill Cycle - should not display ""Error Generating Toolpath"" if ESC is hit" |
Fixed |
|
70625 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
70694 |
"Boundary Enhancements - cut on, cut to and tangent to options" |
Implemented |
|
70716 |
Flatland - does not machine the top face of a solid if negative offset |
Fixed |
|
71025 |
Roughing - Z Offset influences associative Level in certain Features |
Fixed |
|
71140 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
71628 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
71761 |
Template - Mill - Incorrect G code on second hole in cycle |
Fixed |
|
72393 |
Roughing - Z Offset influences associative Level in certain Features |
Fixed |
|
72507 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
72544 |
"Facemill Cycle - should not display ""Error Generating Toolpath"" if ESC is hit" |
Fixed |
|
72566 |
Operations - to support Adaptive Template posts in Turning |
Operations can now be used with the new adaptive code generators. |
|
72772 |
Simulator - New Profiling creates full circle gouging part |
Fixed |
|
72938 |
Memory - Roughing out of memory on some large parts |
Supplied parts now generate a toolpath |
|
73145 |
Facemill - enable leads on all passes with optimised |
With optimised checked you can now specify to apply leads to all cuts or just the first and last pass. |
|
73304 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
73600 |
Simulator - Solid parts digitised as stock fail to go into Simulator |
Solid stock is now healed where possible. |
|
73788 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
73812 |
Roughing - Z Offset influences associative Level in certain Features |
Fixed |
|
73848 |
Operations - to support Adaptive Template posts in Turning |
Operations can now be used with the new adaptive code generators. |
|
73876 |
New Hole Cycle - Chipbreak - parameterise the hard-coded 1mm (0.05in) retract |
Fixed |
|
73878 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
73954 |
Roughing - Level Order Incorrect - Causes Collision |
Fixed |
|
74277 |
Flatland - does not machine the top face of a solid if negative offset |
Fixed |
|
74523 |
Roughing - Z Offset influences associative Level in certain Features |
Fixed |
|
74627 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
74696 |
Facemill - enable leads on all passes with optimised |
With optimised checked you can now specify to apply leads to all cuts or just the first and last pass. |
|
74727 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
74905 |
Open pockets - unsuitable for machining |
New Open Pocket Feature created. |
|
75011 |
"Simulator - add part comparison facility, currently only availablin rapid result" |
Comparison facilty added to Simulator |
|
75126 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
75487 |
Turning B Axis - Move angular sets wrong CAXIS mode |
Fixed |
|
75535 |
Simulator - attached part crashes Simulator |
Fixed. |
|
75555 |
Simulator crashes with MW critical error |
Fixed |
|
75562 |
Flatland - does not machine the top face of a solid if negative offset |
Fixed |
|
75622 |
Roughing - XY offsets and 2.5d geometry fail |
Fixed |
|
75623 |
Simulator - incorrect simulation roughing out a circular bore |
Fixed |
|
75812 |
Profiling 2D - 1 micron FIX causes extra NC on Curves |
Smooth NC output improved |
|
75871 |
"Feature Find - Countersink counterbored hole should be 1 feature, not 2" |
Fixed in New Hole Feature |
|
75879 |
Code Generator - Feedrates wrong for longhand thread mill |
Fixed |
|
75959 |
m/c config - multiple sequences with different setups |
Fixed |
|
75961 |
Edit Apply to All - Regression - Changing Style from None demands a Regen Vector |
Fixed |
|
76009 |
Roughing - Toolpath gouges Inventor model |
Fixed |
|
76093 |
"Rough FWC - with Trochoidal on, part is gouged" |
Fixed |
|
76105 |
Simulator - profiling an axial arc in rotary mode can produce strange results |
Fixed |
|
76231 |
EdgeCAM simulation - reverse axial tool library tool now simulates incorrectly |
Tool orientation display Fixed |
|
76263 |
Simulator - should remember the machine display status settings |
Simulator machine display status now saved to registry |
|
76436 |
Layers Visibility - cannot view layer with number as name |
"In GLView, go to Configure View, and the layers will be off on that single view. Turn them ON to view" |
|
76451 |
Solid Edge CAD Links - to base MM/INCH decision on HoleData::GetUnits( ) |
CADLinks V11 sets Thread units properly. |
|
76515 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |
|
76519 |
Roughing - crashes EdgeCAM at regeneration on attached 9.75 part - regression |
Fixed |
|
76735 |
Rest Rough - ability to use separate boundaries (different stock/boundary) |
Implemented |
|
76803 |
Roughing - Z Offset influences associative Level in certain Features |
Fixed |
|
76828 |
Memory - Roughing out of memory on some large parts |
Supplied parts now generate a toolpath |
|
76851 |
Rough and Finish Turn - Increase X Offset or Z Offset causes a gouge |
Fixed |
|
76866 |
Merge Sequences- Enhancement to sorting logic |
Implemented Maintain Tool Order option |
|
76891 |
Enhance Solid Machinist to Feature Find open pockets |
Implemented |