Cimatron_E_5X_Aerospace_Morph_Between_2_Curves

5x aerospace / morph between 2 curves
user interface
surface paths
  drive surface
  drive surface offset
  round corners
  extend/trim
  pattern
    parallel cuts
    cuts along curve
    morph between two curves
    advanced options
    parallel to curves
    parallel to surface
    project curve
    morph between two surfaces
  cutting area
    full, avoid cuts at exact edges
    full, start and end at exact surface edge
    determined by number of cuts
    limit cuts by one or two points
  sorting
    flip step over
    cutting method
    direction for one way machining
    cut order
    start point
  surface quality
    distance
    maximum stepover
tool axis control
  output format
  maximum angle step
  tilting strategies
    tool axis will not be tilted and stays normal to surface
    tool axis will be tilted relative to cutting direction
    tool axis will be tilted with the angle
    tool axis will be tilted with fixed angle to axis
    tool axis will be tilted around axis
    tool axis will be tilted through point
    tool axis will be tilted through curve
      closest point
      angle from curve
      angle from spindle, main direction
      from start to end
      from start to end for each contour
      automatic curve
    tool axis will be tilted through lines
    tool axis will be tilted from point away
    tool axis will be tilted from curve away
      closest point
      angle from curve
      angle from spindle, main direction
      from start to end
      from start to end for each contour
    side tilt definition
      follow surface iso directions
        allow flipping side direction
        gradual lead angle change
        gradual side tilt angle change
        side tilt fanning distance
        ruled surface radius limit
      ortho to lower edge curve
        allow flipping side direction
        gradual lead angle change
        gradual side tilt angle change
      ortho to cut dir at each pos
        allow flipping side direction
        gradual lead angle change
        gradual side tilt angle change
      use spindle main direction
        allow flipping side direction
        gradual lead angle change
        gradual side tilt angle change
      use user defined direction
        allow flipping side direction
        gradual lead angle change
        gradual side tilt angle change
  run tool
    auto
    center
    radius
    front
    user given point
  tool axis direction limit parameters
    xz limit
    yz limit
    xy limit
    conical angles from leading curve
gouge check
  status
  check
  check gouge between positions
  drive surfaces, check surface
  clearance (gouge check)
  strategy
    retracting tool along tool axis
    moving tool away
      retracting the tool in the x, y and z direction
      retract tool along surface normal
      retract tool away from origin
      retract tool cut to center
    tilting tool away with max angle
    leaving out gouging points
    stop toolpath calculation
link
  first entry
  last exit
  gaps along cut
    direct
    broken feed
    broken feed and rapid
    clearance area
    follow surface
    blend spline
    use both macros
    use entry macro
    use exit macro
  links between slice
    direct, broken feed
    broken feed and rapid
    clearance area
    follow surface
    blend spline
    use both macros
    use entry macro
    use exit macro
  links between passes
    direct
    broken feed
    clearance area
    follow surfaces
    blend spline
    broken feed and rapid
    use both macros
    use entry macro
    use exit macro
  entry macro
    tangential arc
    reverse tangential arc
    vertical tangential arc
    horizontal tangential arc
    orthogonal arc
    tangential line
    orthogonal line
    tool axis orientation
    width/length
    arc sweep/arc diameter
    height
  exit macro
  clearance area
    plane in x, y or z
    cylinder parallel to x, y or z
    sphere
  distances
    rapid distance
    feed distance
    air move safety
roughing
  connect slices by shortest distance
  multi passes
  plunge
  morph pocket
  depth cuts
    use ramp
utility
  feed rates
  change parallel cuts to spiral
  advanced spiral calculation
  calculation based on tool center
  axial shift
  chaining tolerance
machine definition
appendix