Table of Contents

Introduction

I. DesignModeler Descriptions

DMVM1 - Extrude, Chamfer, and Blend Features

DMVM2 - Cylinder using Revolve, Sweep, Extrude, and Skin-Loft

DMVM3 - Extrude, Revolve, Skin-Loft, and Sweep

II. Simulation Descriptions

DSVM1 - Statically Indeterminate Reaction Force Analysis

DSVM2 - Rectangular Plate with Circular Hole Subjected to Tensile Loading

DSVM3 - Modal Analysis of Annular Plate

DSVM4 - Shape Optimization of a Quarter of a Plate With Hole

DSVM5 - Heat Transfer in a Composite Wall

DSVM6 - Heater with Nonlinear Conductivity

DSVM7 - Thermal Stress in a Bar with Temperature Dependent Conductivity

DSVM8 - Heat Transfer from a Cooling Spine

DSVM9 - Stress Tool for Long Bar with Compressive Load

DSVM10 - Modal Analysis of a Rectangular Plate

DSVM11 - Large Deflection of a Circular Plate with Uniform Pressure

DSVM12 - Buckling of a Stepped Rod

DSVM13 - Buckling of a Circular Arch

DSVM14 - Harmonic Response of a Single Degree of Freedom System

DSVM15 - Harmonic Response of Two Storied Building under Transverse Loading

DSVM16 - Fatigue Tool with Non-Proportional Loading for Normal Stress

DSVM17 - Thermal Stress Analysis with Remote Force and Thermal Loading

DSVM18 - A Bar Subjected to Tensile Load with Inertia Relief

DSVM19 - Mixed Model Subjected to Bending Loads with Solution Combination

DSVM20 - Modal Analysis for Beams

DSVM21 - Buckling Analysis of Beams

DSVM22 - Structural Analysis with Advanced Contact Options

DSVM23 - Curved Beam Assembly with Multiple Loads

DSVM24 - Harmonic Response of a Single Degree of Freedom System for Beams

DSVM25 - Stresses Due to Shrink Fit Between Two Cylinders

DSVM26 - Fatigue Analysis of a Rectangular Plate Subjected to Edge Moment

DSVM27 - Thermal Analysis for Shells with Heat Flow and Given Temperature

DSVM28 - Bolt Pretension Load Applied on a Semi-Cylindrical Face

DSVM29 - Elasto-Plastic Analysis of a Rectangular Beam

DSVM30 - Bending of Long Plate Subjected to Moment - Plane Strain Model

DSVM31 - Long Bar with Uniform Force and Stress Tool - Plane Stress Model

DSVM32 - Radial Flow due to Internal Heat Generation in a Copper Disk - Axisymmetric Model

DSVM33 - Electromagnetic Analysis of a C-Shaped Magnet

DSVM34 - Rubber cylinder pressed between two plates

DSVM35 - Thermal Stress in a Bar with Radiation

DSVM36 - Thermal Stress Analysis of a Rotating Bar using Temperature Dependant Density

DSVM37 - Cooling of a Spherical Body

DSVM38 - Crashing Blocks Simulation with Flexible Dynamics Analysis

DSVM39 - Transient Response of a Spring-mass System

DSVM40 - Deflection of Beam using Symmetry and Anti-Symmetry

DSVM41 - Brooks Coil with Winding for Periodic Symmetry

DSVM42 - Hydrostatic Pressure Applied on a Square Bar with Fully, Partially Submerged in a Fluid

III. DesignXplorer Descriptions

DXVM1 - Optimization of L-shaped cantilever beam for deflection, volume, and stress under axial load

DXVM2 - Optimization of bar with temperature-dependent conductivity for temperature and thermal strain

DXVM3 - Optimization of water tank column for mass and natural frequency when subjected to direct compressive and buckling stress

DXVM4 - Optimize frequency of plate with simply supported at all it's vertices

DXVM5 - Optimization of buckling load multiplier with CAD parameters and Young's modulus

DXVTVM1 - Structural Analysis of Annular Plate with CAD and Material Parameters

DXVTVM2 - Modal Analysis of a Rectangular Plate

DXVTVM3 - Thermal Analysis of a Rectangular Bar